Відео

I Saw Most HVAC Techs don't clean the joints before Brazing. But it will always better to clean the joints

Pro Tip Soldering VALVES: Never use a Tin/Silver solder (Lead Free) on any valve! You will overheat it due to much higher melting temperature needed. On valves use 60/40 or 50/50 LEAD! Especially ZONE valves! You're welcome.

Can you install shark bite on copper pipe that has a green tinge to it, I get you have to clean the pipe will that get rid of the green tinge

Thanks so much. We have an LG washer and really needed 2 of these. Prior to viewing your video, I wasn’t aware they existed. I’ve learned a lot from you.

ProPex (Pex A) is total Garbage. Contractors love it because this shit will leak in 5-10 years, more money for them.

They are pure garbage and do not do anything. Install a water expansion tank instead.

If you have water in the pipe How are you going to unsolder it ?

Now do the aviation version! Let's see that poop move in a modern airliner toilet faster than a Formula 1 race car!

Brilliant

Thank you. I knew the process, but not the names of all the materials.

So at 4:40 let's say it's at code, the vent lins is at 6 incest above the fixture.. Year later the house is remodeled and they put in a vanity that's an qnch higher, now the vent line only 5 inches above, now it fails code?

So, under a sink you can't have a 90 turn pipe?

Smooooooth

Good job🎉🎉🎉

I tried foil once and it will melt a hole easily

Boy, back in My day We soldered

Is ok to use Tinning Flux for copper pipes with Brass Fittings?

And den?

I’m starting to see why everyone is switching to PEX A

Use plastic male when transitioning to metal.

goddamn did john consent to his testicles going live

Sir please continue polity question series 😢

“Pretty cool, huh?” Lmaooo been a while since I heard that

Thanks for the explanation. It was very clear it thought me lots wish when it was soldigng make it slower but all really great thanks much for that video

Thank you. Good video

That's nuts. 😂

The fun thing about Propress fittings is they may not start leaking until months after assembly.

Calling people “weekend warriors,” man we’re just out here trying to figure out how to not go broke in this economy. Tradesmen are expensive. And let’s be honest, most things can be learned on UA-cam.

My man did not need to draw in the balls

Watching this in the toilet doing the same thing😃

Thank you so much for this. also I thought it was extremely cool that you went to the trouble to actually cut this joint in half so that everyone can see what’s happening on the inside. This is such a great video.

😂😂😂

Get a spray bottle of water and soak any dry wood at risk of igniting near where you are sweating.

As a new construction plumber, I got a piece of hardy panel a while back, and I use that. For a heat shield For the first one, I use a pair of channel locks. They're more convenient since they're in my bag already

Skibidi toilet 😬😬😬😬

So no cleaning with sand paper or wire brush?

The family jewls got me so badly freaking hilarious 🤣🤣🤣🤣🤣😂😂😂😂😂

Help! Repairing 1/2 inch copper tubing. Got my leak cut out, deburring done on both ends, inside & out. 1/2 inch Push fittings were too loose, so I got 1/2 inch brass Compression fittings kit (5 pack). Everything fits fine, except the seal rings. What's my next move? Thanks. 💖 PS I tried checking your forum, but this had not been addressed yet, so I created a thread under Help!

ONe of the best plumbing videos without a doubt! Great live graphics too. Thank you!

Basically toilets waste 6 litres everyday meaning toilets waste 100 thousand litres a year

Can the water pressure regular be fully tight but the pressure is still high?

Great video - learned a few clever tips and techniques. Thanks!

EWWWW..

I used this yesterday to fix my water heater piping and it worked! I just follow his theory of the solder is attracted to heat. And no leaks!

I'm assuming S traps are common in manufactured homes.

John’s work and his nuts are best part of animation 😂

I tried to unsolder and couldn’t do it. I don’t know why, if someone can explain me.

Don't understand why you didn't use thread tape?

Thank you so much this was a big help.